
    ZoneOS ZoneScreen for Windows XP

 1. Installation.
Run setup script (named setup.bat or just setup, depending on folder view
settings) and follow provided instructions.

Sections 2, 3 and 4 describes behaviour of setup script. You may use these
instructions instead of running setup script.

 2. Installation 'by hand'.
Extract applicationf files, for example, into
'C:\Program Files\ZoneScreen'. ZoneScreen could be removed by removing these
files. Also, if ZoneScreen display driver is installed, it should be
uninstalled in case you are removing ZoneScreen.
To run ZoneScreen Wizard, click zsserver.exe (blue icon with 'x2' named
zsserver or zsserver.exe, depending on folder view settings).

 3. Installing ZoneScreen display driver 'by hand'.
If you want to use ZoneScreen for extending your desktop, you need to install
ZoneScreen display driver (otherwise, if you will use ZoneScreen only for
mirroring, you could skip sections 2 and 3).
You can do this by following:
2.1 In 'Control Panel' start 'Add Hardware' wizard. If your control panel is
in category view, 'Add Hardware' is absent. To switch to classic view, click
'Switch to Classic View' in control panel task list.
2.2 Click next to allow system to scan for new hardware. Since network
display is only driver, no hardware is required for it.
2.3 Select 'Yes, I have already connected the hardware.'
2.4 In the supplied list of devices, select 'Add a new hardware device item.'
2.5 Since Windows do not know anything about ZoneScreen, select
'Install the hardware that I manually select from a list (Advanced).'
2.6 In the list of hardware classes, select 'Display adapters'.
2.7 Click 'Have Disk' button.
2.8 Navigate to zonescreen.inf file located in the root of ZoneScreen folder,
e.g. to 'C:\Program Files\ZoneScreen\zonescreen.inf'. Note that by default
Windows hides extensions for known file types and you may see only
'zonescreen' instead of 'zonescreen.inf'.
2.9 'ZoneScreen virtual display driver' should appear in the list of models
after you have specified path for zonescreen.inf. Select it and click 'Next'.
2.10 Before loading driver you will be warned about not signed driver.
Click 'Continue Anyway' to proceed.

 4. Removing ZoneScreen display driver 'by hand'.
If you no loger need it, you may unload display driver by following:
3.1 Right-click on 'My Computer' and select 'Manage' item in the list.
3.2 In the left pane, select 'Device Manager'.
3.3 Expand 'Display adapters' in the right pane (list of system devices).
3.4 Right-click 'ZoneScreen virtual display driver' and select 'Uninstall'.
3.5 As this driver can't be unloaded dynamically, device will be deleted
only after computer reboot. You are not obligated to reboot immediately,
it's only for applying changes to the system configuration.

 5. Starting server application.
In ZoneScreen wizard select 'Act as a server' radio button, then select
port name and monitor you want to redirect. Port number must be the same
for both client and server wizards. If you wish to use port number,
different from default value, change it in both client and server side
wizards. When you selecting monitor, left-top corner is shown as a
screenshot. On next page, press 'Start' button to begin accept incoming
client connection. Use 'Reload' button to dynamically change FPS transfer
rate (frames per second to send to client).

 6. Adjusting resolution and color depth.
At server machine right-click on the desktop, and select 'Properties'.
In 'Settings' tab of 'Display Properties' dialog you will see all
moitors available to system. Check 'Extend my Windows
desktop onto this monitor' checkbox for each monitor you are going to
use with ZoneScreen. If there is only one monitor, this item is absent.
You may adjust monitor resolution and color depth on the same page,
but some modes could be hidden by Windows. If you need more modes,
click 'Advanced' button, then enter 'Adapter' tab and click 'List All
Modes' button to select mode in the list of all modes supported by monitor.
Note that even in this case some modes (320x240, 480x640, etc) are hidden.
You may select required mode in monitor selection page in ZoneScreen wizard:
combo-box contains all modes supported by display driver for currently
selected monitor, and you may set required mode by selecting in the box.

 7. Connecting to server.
For ZoneScreen to work you need network connection between your client and
server computers (computers are both connected to the same network, or
connected directly with cross-over cable or 1394 firewire cable, etc).
Once ZoneScreen is installed on both client and server machines, you may
connect to server from client machine by selecting 'Act as a client' and
specifying server port number and server host name. ZoneScreen wizard at
server (server application) must be started prior to connecting to server.
Error message 'Destination host unreachable' mean your have specified
incorrect port or host name, or specified port is blocked by server firewall,
or server application is not started.

 8. Receiving video signal.
If client was able to connect to server, it starts showing video signal wich
it receive from server. You may switch client into full-screen mode by
pressing Alt+Enter. To exit full screen, press Alt+Enter again.

 9. ZoneScreen wizard command line options.
ZoneScreen wizard supports entering settings using command line. Full list of
available options and examples you may find with command 'zsserver /?'.
